Description | | DISCLAIMER:
At U.S. PATRIOT ARMORY, we by no means provide legal advice or legal counsel. Every builder needs to research their respective City, State and Federal laws in the area they are ordering from. We DO NOT provide gunsmithing advice. U.S. PATRIOT ARMORY is not responsible for improper builds, damage or injury due to user error.
* Our products are not sold or shipped to residents of New Jersey
WILL NOT SHIP 80% Lowers to the following areas: NAVADA, WASHINGTON DC, WASHINGTON, RHODE ISLAND, DELAWARE, NEW YORK, MASSACHUSETTS, CONNECTICUT, NEW JERSEY, HAWAII, MONTGOMERY COUNTY-MD, PHILADELPHIA-PA, SACRAMENTO-CA, SAN FRANSISCO-CA and LOS ANGELES-CA | Please note: We are not able to legally ship to NY, NJ, CT, RI, or DC. If you place an order with a shipping address for one of these states, the order will be canceled. | | Shipping Restrictions
AR-15Lowerreceivers.com only ships within the United States. Federal legislation dictates we cannot ship our products internationally. Shipping of various parts and/or accessories are prohibited to states and locales (ie New Jersey, California, New York, etc…) with restrictions against certain parts and/or accessories (i.e. states with high-capacity magazine restrictions, manufacturing of semi-automatic weapons, etc..). It is your responsibility to be aware of your local firearms laws before purchasing from our website. We try our best to keep our shipping page current, but laws change daily. | |
Content |
AR15 80% Lower Receiver Bulk 5 Pack Black Anodized and Jig
These 80% Lower receivers for AR 15 are machined to mil-spec tolerances which make them perfect for the DIY Gunsmith. The Mag well is fully broached on all our AR-15 80% lowers for a perfect fit every time.
80% AR 15 Lower receivers are machined from 7075-T6 forgings
The operations left to be completed on the 80 percent lower receivers are as follows:
- fire control group
- trigger pin
- hammer pin
- trigger slot
- safety selector hole.
This is a not an FFL item. This is not a complete AR-15 Lower receiver and still requires machining to be completed.
80% AR 15 Lower Receiver Jig Set
- KIT INCLUDES RIGHT AND LEFT SIDE PLATES, 3 TOP PLATES AND SCREWS
- Every piece is replaceable on the jig in case there is a mistake made in manufacturing of your 80% AR Lower
- There are three top plates that are interchangeable to allow you to mill the fire control group.
- The side plates are fit with drill bushings to allow you to properly drill the trigger and hammer pin.
- A complete set of Top plates and Side plates are included with this 80 percent jig set.
- You may order more top plates separately if they get damaged.
The AR15 80% lower receiver jig kit comes with complete instructions to help you finish your AR 15 lower Project.
Weight |
12 lbs |
Brand |
Daytona Tactical |
Color |
Black |
Platform |
AR-15 |
| AR-15 JTE 80% LOWER RECEIVER - BLACK ANODIZED - NO LOGO
- Type 3 Black Anodized or raw finish.
- T6 Heat-Treated 6061 Billet Aluminum
- Completed weight: 8 ounces
- Integral winter trigger-guard for added strength
- Flared magwell to improve mag changes.
- Broached magwell
- Lifetime warranty against manufacture defects
| DESCRIPTION
- Manufactured in our own precision machine shop right here in Greer, South Carolina.
- Raw (Non-Anodized)
- Forged in 7075-T6 Aluminum
- Broached and Flared Magwell
- Tumbled and Hand De-Burred
- ATF Approved
ALL PAID ORDERS WILL BE SHIPPED ASAP! FORGINGS ON HAND AND MACHINING 24/7!
What is an 80% Lower Receiver?
This 80% lower receiver is manufactured in the USA in our precision machine shop in Greer, South Carolina. Sometimes referred to as a “paperweight”, the 80% lower is not considered a firearm or a complete receiver until you finish it. Therefore, no FFL is required in order to buy or ship the product.
When you are looking to build out your AR, buy the American-made 80% forged lower from Palmetto State. Nothing leaves our machine shop that doesn’t meet our precision standards for quality. You can be assured of a highly accurate and aligned lower. Made with forged 7075 aluminum, your 80% lower is built with the strongest aluminum and provides a slight advantage in weight compared to a billet option.
Some manufacturers use cheaper aluminum and are not as concerned with precision machining, leaving you dissatisfied with an inferior product. At Palmetto State Defense, we stand behind the quality of our 80% lowers.
With an 80% forged lower, there is no serial or registration required since it is not a firearm. If you live in a not-so-friendly gun state, be sure you are well aware of the laws before purchasing.
| AM-15 80% Lower Receiver, Unfinished, Open Trigger
No FFL is required to purchase this item.
California requires 80% Receivers to be serialized before fabrication. California residents must submit to a background before building. Other states have banned the sale, ownership, manufacture, and use of 80% Receivers. Because of changing firearm laws, this list may not be all-inclusive. The following are the states that have banned 80% receivers: NJ, NY, CT, HI, DC and RI. | Description
(1) Raw 80% Lower Billet Receiver:
- Color: Raw - no anodization
- 100% Mil-Spec
- Quantity: 1
- Fire/Safe Marked: Yes
- Oversized built-in trigger guard
- Rear takedown lug is pre-milled
- Billet 6061-T6 Aluminum
- 100% Made in the USA
- NO FFL REQUIRED
No FFL is required to purchase this lower receiver. This Billet 6061-T6 Aluminum 80% lower receiver is not considered a firearm and is compliant with the gun control act of 1968 and not classified as a firearm as defined in 18 U.S.C. 921(a)(3).
| Description
Shipping Status: Ships in 3-5 Days! (See the Shipping/Returns webpage for updates)
All machining processes for our Black Anodized Skeletonized AR 15 80% Lower are completed other than drilling/milling the FCG (Fire Control Group) pocket and trigger slot, and drilling the Selector switch, Trigger and Hammer pin holes.
– Mates with any mil-spec AR-15 upper receiver
– CNC Machined from 6061-T6 Billet Aluminum
– Rear lug pocket already machined
– ‘Pictogram’ style Fire-Safe Engravings
– Integral trigger guard for added overall strength
– Machined (not broached) skeleton Mag Well with wide flare
– Ltd lifetime warranty against manufacturer defects
Optional:
– Bolt release pin hole Drilled and Tapped 6-32
– Cerakote Graphite Black
Availability / Shipping:
Our black anodized skeletonized AR 80 Percent Lowers are typically backordered, but please see our Shipping/Returns webpage for the latest shipping details. |
Reviews
There are no reviews yet.