16″ Zombie Green AR-15 Rifle Kit 15″ Keymod Handguard With 80% Lower
16″ AR-15 Rifle kit zombie green upper, lower, and handguard. The upper receiver has M4 Feed Ramps with a Nitride 1×7 barrel (Includes zombie green 80 percent Stripped Lower Receiver). This rifle kit contains all components to complete YOUR Rifle except Magazine and Sights
Keymod Accessory Rails Found here.
This is not an FFL Item because 80% Stripped Lower Receiver is not fully Machined and needs Machining to complete lower receiver.
Chamber – .223 / 5.56 M4 Feed Ramp (Shoots both .223 and 5.56)
Twist – 1 × 7
Barrel Thread – 1/2×28
Barrel Steel – 4150 Chrome Moly / Nitride Processed
Flash Hider – A2 Flash Hider
Handguard – 15″ Slim Zombie Green Keymod
Gas Block -.750 Low Profile gas block, Carbine Gas Tube with Pin
Upper Receiver – Zombie Green M4 Flat-top Upper 7075 T6
Bolt Carrier Group – Milspec M-16 Bolt/Carrier assy
Charging Handle – Included
Lower Parts Kit – Milspec Lower Parts Kit with Black Magpul Moe Grip
Stock – Black Magpul Moe Mil-Spec
||1 x 7
||1/2" x 28
|Barrel Gas Block
|Barrel Gas System
What is an Anodized 80% Lower Receiver?
You can rest assured of quality with this Anodized 80% Lower Receiver. All of our products are made in Greer, SC in our precision machine shop.
With an 80% lower, it is often referred to as a “paperweight” or a “ghost gun”. Until you complete your build, the 80% lower is not considered a firearm or a complete receiver. Because it’s not a firearm, no FFL is necessary to buy, ship, or receive the product.
When the lower comes anodized, as ours does here, it has had a protective coat created by oxidizing the aluminum. This is sometimes also referred to as a hard coat. The anodization helps to protect the lower from wear and tear, as well as any potential corrosion.
If you are considering building out an AR-15, buy the made in the USA Anodized 80% Forged Lower from Palmetto State. We stand behind the quality of our products and don’t let anything leave our shop without meeting our quality and precision standards.
We guarantee the accuracy and alignment of our lowers. Your 80% lower is built with the strongest aluminum (7075) and provides a slightly lighter feel compared to a billet option.
With an 80% forged lower, there is no serial or registration required since it is not a firearm. If you live in a not-so-friendly gun state, be sure you are well aware of the laws before purchasing.
Please note: We are not able to legally ship to NY, NJ, CT, RI, or DC. If you place an order with a shipping address for one of these states, the order will be canceled.
.308 80% Lower Receiver & Jig
Includes a jig and all the drill bits.
After two years of planning, design, engineering, and testing, we're proud to introduce the industry's first reinforced polymer receiver designed for the DPMS styled .308 in an 80% format.
- Industrial strength, finest reinforced polymer material....nothing held back.
- Feel the difference the second you pick it up.
- Rock solid frame, injection molded from a fully automated system that was two years in the making.
The .308 80% Lower Receiver Design features:
- Unique reinforced polymer design with solid core design
- ATF compliant design
- Beefed up buffer tube ring and ribbing across the entire upper surface area.
- No-thread design on pistol grip area.
- Stiffened magwell, ultra-light design.
- See product page for additional parts list
Is it legal?
YES! The 308 unit is well within the defined parameters of a "reciever blank" defined by the ATF and therefore has not yet reached a stage of manufacture that meets the definition of firearm frame or receiver found in the Gun Control Act of 1968 (GCA).
P80-308 Kit List: Each Lower and Jig Kit comes with the following:
||Qty per Lower
||308 Lower Receiver
||Pistol Grip Nut
||Pistol Grip Screw
||Qty per Lower
|Warrhogg .308 Jig
|End-Mill Bit with Laser Etched Depth Mark
||7/16" end mill bit
|Drill Bit, Safety Selector Switch Hole
||3/8" drill bit
|Drill Bit, Pin Holes for Trigger & Hammer
||5/32" drill bit
|Drill Bit, for Trigger Hole
||5/16" drill bit
||The 80% Machined Lower isn't finished and comes in raw aluminum ready for your coating of choice. Made from 7075-T6 and features a 3/4 inch grip screw. These 80% Lowers are Designed off the AR-15 Platform.
No FFL is required to purchase this 80% Lower.
Please note that the rear lug pocket for the upper must be finished in the machining process in order to seat an upper
California requires 80% Receivers to be serialized before fabrication. California residents must submit to a background before building. Other states have banned the sale, ownership, manufacture, and use of 80% Receivers. Because of changing firearm laws, this list may not be all-inclusive. The following are the states that have banned 80% receivers: NJ, NY, CT, HI, DC and RI.|
(1) Black Fire/Safe Marked AR15 Forged 80% Lower Receiver:
No FFL is required to purchase this lower receiver. This forged 7075 aluminum 80% lower receiver is not considered a firearm and is compliant with the gun control act of 1968 not classified as a firearm as defined in 18 U.S.C. 921(a)(3)
- For AR-15 builds (5.56/.223/300 BLK/6.5 Grendel)
- Color: Anodized Black
- Type III Hard Anodized
- 100% Mil-Spec
- Quantity: 1
- Fire/Safe Marked: Yes
- Forged 7075-T6 Aluminum
- Broached Magwell
- 100% Made in the USA
- NO FFL REQUIRED
Every AR build starts from the ground up with a good lower receiver. Start yours in style with this badass 80% lower receiver by Outdoor Ops. This beauty comes to you in graphite black, so you can make sure that aesthetically, your build will look as awesome as it performs. See below for additional details.
- Machined from American-made Mil-Spec 6061 aluminum billet
- Graphite Matte Black Cerakote finish
- Threaded bolt catch hole (threaded pin not necessary for function)
- Armalite™ style (standard, mil-spec) lower parts kit compatible
- Accepts standard and PMAG™ magazines